The BaitShop Homepage
Forum Home Forum Home > FireArms, et cetera > Handguns, Pistols and SixGuns
  New Posts New Posts RSS Feed - A new 44 mag.
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

This site is completely supported by donations; there are no corporate sponsors. We would be honoured if you would consider a small donation, to be used exclusively for forum expenses.



Thank you, from the BaitShop Boyz!

A new 44 mag.

 Post Reply Post Reply
Author
Message
tj3006 View Drop Down
.416 Rigby
.416 Rigby

AKA King Leui VX-III

Joined: 16 June 2003
Location: United States
Status: Offline
Points: 2373
Post Options Post Options   Thanks (0) Thanks(0)   Quote tj3006 Quote  Post ReplyReply Direct Link To This Post Topic: A new 44 mag.
    Posted: 29 January 2016 at 13:17
      Not brand new but new to me.
     Its a Model 29. Has a 6.5 inch barrel and is new
enough to have the stupid key lock.
      I put together Some hand loads with 240 grain
Hornady XTPs and W 296.
      If i remember correctly. S&W Made some changes to
the 29 To make it a little stouter.
       I think they did this before the key lock was
added. Does anyone remember ?
       This 1st batch is well below book max , but i
pland to stiffen them up a bit over time.
    Opinions please...tj3006
Freedom 1st tj3006
Back to Top
Wing master View Drop Down
Administrator
Administrator
Avatar
AKA StraightShooter

Joined: 10 June 2003
Location: United States
Status: Offline
Points: 7481
Post Options Post Options   Thanks (0) Thanks(0)   Quote Wing master Quote  Post ReplyReply Direct Link To This Post Posted: 29 January 2016 at 14:30
tj,

What is the dash number? That's the number after the model number. This indicates the production changes it has.

The endurance package was added in 1987 to the model 29-3. Their were very few of these made. They were preparing for the 29-4.

The 29-8 was introduced in 2001 with the internal lock.

I assume yours is a 29-8. If it's a 29-9 it would be a performance center gun.

One other option is it could be the 44 Classic. These have a full lug barrel. This is unlikely though because they were discontinued in 1994. I am not sure, but I don't think any of them have the internal lock.

Wing master
I have always considered myself to be quite the bullshitter, But ocasionally it is nice to sit back and listen to a true professional......So, Carry on.
Back to Top
CB900F View Drop Down
Administrator
Administrator
Avatar
Honor, Integrity

Joined: 10 June 2003
Location: Eritrea
Status: Offline
Points: 8857
Post Options Post Options   Thanks (0) Thanks(0)   Quote CB900F Quote  Post ReplyReply Direct Link To This Post Posted: 30 January 2016 at 03:42
Tj;

If I remember correctly, the general opinion is that the
pre-lock guns have a better factory trigger than the post-
lock guns. And, that the post-lock trigger is a screaming
beach to work on to get it up to par.

I've only got one post-lock S&W, and it's a 617/10. I do
know the trigger on that example isn't as good as a couple
of pre-lock guns I've handled.

900F
Birth certificate!? He don't need no steenkink birth certificate!!
Back to Top
tj3006 View Drop Down
.416 Rigby
.416 Rigby

AKA King Leui VX-III

Joined: 16 June 2003
Location: United States
Status: Offline
Points: 2373
Post Options Post Options   Thanks (0) Thanks(0)   Quote tj3006 Quote  Post ReplyReply Direct Link To This Post Posted: 30 January 2016 at 10:37
My revolver is a Mdl-29-8
   The single action trigger is excellent !
I tried it out today at 25 yards.
   My Dumb self forgot to bring a screw driver to
adjust the sights.
   It was shooting quite high. But I kept all my shots
on the paper.
   I intend to order some lighter cast bullets and
develop some skill.
    I did a ton of revolver shooting in my early 20s.
But i,m 56 now. Bifocals will take some getting used
to.
     So if i understand your very hepfull post wing
master.My 29-8 is not a weapon i need to baby. Just
take care of it and don't do anything stupid and and
should be just fine ! Correct ?...tj3006
Freedom 1st tj3006
Back to Top
CB900F View Drop Down
Administrator
Administrator
Avatar
Honor, Integrity

Joined: 10 June 2003
Location: Eritrea
Status: Offline
Points: 8857
Post Options Post Options   Thanks (0) Thanks(0)   Quote CB900F Quote  Post ReplyReply Direct Link To This Post Posted: 30 January 2016 at 12:20
Tj;

T'were me, I'd stay about one grain under max with a 240
grain jacketed bullet. That should still get you a
muzzle velocity in the high 1300's to very low 1400's. I
would think that'd be enough to do any reasonable job.

Plugging in reasonable numbers to the JBM calculator
gives these results using a 240 grain bullet, .170 B/C at
1400 fps muzzle with a 25 yard zero. Results rounded to
nearest whole number.

25 yards 1330 fps & 942 ft. lbs.
50 yards   1256 fps & 841 ft. lbs. with 1.4"   drop.
75 yards   1190 fps & 755 ft. lbs. with 3.6"
100 yds    1134 fps & 685 ft. lbs. with 6.2" drop.

900F





Edited by CB900F
Birth certificate!? He don't need no steenkink birth certificate!!
Back to Top
Wing master View Drop Down
Administrator
Administrator
Avatar
AKA StraightShooter

Joined: 10 June 2003
Location: United States
Status: Offline
Points: 7481
Post Options Post Options   Thanks (0) Thanks(0)   Quote Wing master Quote  Post ReplyReply Direct Link To This Post Posted: 30 January 2016 at 17:16
You're absolutely correct tj.

I don't think you could wear it out in your lifetime.

If you look at a reloading manual from the 50's or 60's you will notice the max loads are quite a bit higher than they are in a newer manual. Some of those old loads were pretty hot.

If you load according to a newer manual you should never have a problem.

Congratulations. That's a nice gun.

Wing master
I have always considered myself to be quite the bullshitter, But ocasionally it is nice to sit back and listen to a true professional......So, Carry on.
Back to Top
Wing master View Drop Down
Administrator
Administrator
Avatar
AKA StraightShooter

Joined: 10 June 2003
Location: United States
Status: Offline
Points: 7481
Post Options Post Options   Thanks (0) Thanks(0)   Quote Wing master Quote  Post ReplyReply Direct Link To This Post Posted: 30 January 2016 at 17:24
The Hammer and trigger on Smith & Wessons starting about 1991 are made using a metal injection molded process.

The older ones were machined forged steel.

The MIM triggers have the reputation of not being as good as the earlier ones. In reality most of them are just as good. I think the MIM triggers are probably harder to smooth up if you didn't get a good one.

That being said, I only collect pre MIM pre lock S&W's.

Wing master
I have always considered myself to be quite the bullshitter, But ocasionally it is nice to sit back and listen to a true professional......So, Carry on.
Back to Top
tj3006 View Drop Down
.416 Rigby
.416 Rigby

AKA King Leui VX-III

Joined: 16 June 2003
Location: United States
Status: Offline
Points: 2373
Post Options Post Options   Thanks (0) Thanks(0)   Quote tj3006 Quote  Post ReplyReply Direct Link To This Post Posted: 30 January 2016 at 19:03
    I ordered 100 250 grain bullets from beartooth .
I will back down for awhile till i get better.
    I remembered an old trick. Load only 4 in your
cylinder. When you click on an empty chamber , you will
know if you are flinching...tj3006
Freedom 1st tj3006
Back to Top
BEAR View Drop Down
Administrator
Administrator
Avatar

Joined: 07 September 2013
Location: Appalachian Mtn
Status: Offline
Points: 13734
Post Options Post Options   Thanks (0) Thanks(0)   Quote BEAR Quote  Post ReplyReply Direct Link To This Post Posted: 01 February 2016 at 01:44
dirty harry gun!
Back to Top
tj3006 View Drop Down
.416 Rigby
.416 Rigby

AKA King Leui VX-III

Joined: 16 June 2003
Location: United States
Status: Offline
Points: 2373
Post Options Post Options   Thanks (0) Thanks(0)   Quote tj3006 Quote  Post ReplyReply Direct Link To This Post Posted: 14 February 2016 at 11:28
My gun is neither dirty nor Hairy !
   I loaded some practice rounds today. I am taking a
lady friend shooting tomorrow.
   I used a lee dipper , and 2400 under the 240 grain
XTP.
    The load should give around 1100 fps, so there will
be some recoil, but i still have 20 stiff loads should
she want to try them.
    I might bring the Marlin 94 44 along to cause its
much more fun to hit what you shoot at...tj
Freedom 1st tj3006
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.